MOXA ICF-1150 Series

SPHINX in Europe
SE
  • AT
  • BE
  • DK
  • FR
  • DE
  • IE
  • IT
  • NL
  • ES
  • SE
  • CH
  • UK
Produktgrupper > Media-Converter > MOXA ICF-1150 Series

MOXA ICF-1150 Series

Industrial serial-to-fiber converters

MOXA ICF-1150 Series
2450_12177.png
2450_8533.png
2450_12178.jpg
  • EgenskaperEgenskaper
  • BeskrivningBeskrivning
  • Further InformationFurther Information
  • PDFPDF
  • RS-232, fiber, and RS-422/485 3-way communication
  • Rotary switch to change the pull high/low resistor value
  • Extend RS-232/422/485 transmission up to: · 40 km with single-mode · 5 km with multi-mode
  • 3-way Galvanic Isolation (for "I" model only)
  • - 40 to 85°C wide temperature models available
  • Class I, Div. II certifi cation (Pending)
Industrial serial-to-fiber converters

Three-Way Communication
The ICF-1150 series support 2 serial ports, with a D-sub connector for RS-232 communication and a removable terminal block for RS-422 or RS-485 communication. The 3 ports (2 serial ports and one fiber port) are completely independent. When an ICF-1150 converter receives data from any one port, it will send the data out through the other 2 ports. For example, once the ICF-1150 converter receives a command from the remote master through the fiber port, it will convert the signal and send the command through the RS-232 and RS-422/485 ports at the same time. If the user is monitoring a system running on an RS-485 network, there is no need to use an additional RS-232 to RS-485 converter to connect the laptop computer’s serial port to the RS-485 bus.

Rotary Switch for Setting the Pull High/Low Resistor
The RS-485 interface supports multi-drop or daisy-chain connections, which system engineers will use to connect serial devices such as meters, RTUs, and readers together on the same bus. Since the number of serial devices on the same bus will cause the impedance of the data line to increase, the ICF-1150 allows users to tune the pull high/low resistor. Just rotate the switch to the appropriate value without removing the ICF-1150 from the DIN-rail.
ProdGrafik

Optical Fiber Side

Fiber Connector
SC or ST

Cable Requirements
Single-mode: 8.3/125, 8.7/125, 9/125, or 10/125 ìm
Multi-mode: 50/125, 62.5/125, or 100/140 ìm

Transmission Distance
Single-mode: 40 km
Multi-mode: 5 km

Wavelength
ICF-1150-S (single-mode): 1310 nm
ICF-1150-M (multi-mode): 850 nm

Tx Output
ICF-1150-S (single-mode): > -5 dBm
ICF-1150-M (multi-mode): > -5 dBm

Rx Sensitivity
ICF-1150-S (single-mode): -25 dBm
ICF-1150-M (multi-mode): -20 dBm

Ring Transmission
Half-duplex

Point-to-Point Transmission
Half-duplex or full-duplex


RS-232/422/485 Side

RS-232 Signals
TxD, RxD, GND

RS-422 Signals
TxD+, TxD-, RxD+, RxD-, GND

RS-485-4w Signals
TxD+, TxD-, RxD+, RxD-, GND

RS-485-2w Signals
Data+, Data-, GND

Baudrate
50 bps to 921.6 kbps

ESD Protection
15 kV for all signals

Isolation
2 kV RMS isolation per I/O port for 1 minute


Physical Characteristics

Housing
Metal

Dimensions
30.3 x 70 x 115 mm (1.19 x 2.76 x 4.53 in)

Weight
330 g


Environmental Limits

Operating Temperature
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 85°C (-40 to 185°F)

Storage Temperature
-40 to 85°C (-40 to 185°F)

Ambient Relative Humidity
5 to 95% (non-condensing)


Power Requirements

Input Voltage
12 to 48 VDC

Power Consumption
ICF-1150: 127 mA @ 12 V
ICF-1150I: 163 mA @ 12 V

Voltage Reversal Protection
Protects against V+/V- reversal

Over Current Protection
1.1 A (protects against two signals shorted together)


Standards and Certifications

Safety
UL 508

Hazardous Location
UL/cUL Class I Division 2 Groups A/B/C/D, ATEX Zone 2 EEx nC IIC, IECEx

EMC
CE, FCC

EMI
EN 55022 Class B, FCC Part 15 Subpart B Class B

EMS
EN 61000-4-2 (ESD) Level 4,
EN 61000-4-3 (RS) Level 2,
EN 61000-4-4 (EFT) Level 4,
EN 61000-4-5 (Surge) Level 3,
EN 61000-4-6 (CS) Level 2,
EN 61000-4-8 (PFMF) Level 3

Freefall
IEC 60068-2-32

Green Product
RoHS, CRoHS, WEEE


MTBF (mean time between failures)

Time
792,085 hrs

Database
Telcordia (Bellcore), GB

Water and Dust Proof
IP30



Ordering Information

Model No. Description
ICF-1150-M-SC Industrial RS-232/422/485 to multimode fiber converter, SC connector
ICF-1150-M-ST Industrial RS-232/422/485 to multimode fiber converter, ST connector
ICF-1150-S-ST Industrial RS-232/422/485 to single mode fiber converter, ST connector
ICF-1150I-S-ST Industrial RS-232/422/485 to single mode fiber converter, ST connector,
2 KV isolation
ICF-1150I-M-SC Industrial RS-232/422/485 to multimode fiber converter, SC connector,
2 KV isolation
ICF-1150-M-SC-T Industrial RS-232/422/485 to multimode fiber converter, SC connector,
-40 to 85°C
ICF-1150-M-ST-T Industrial RS-232/422/485 to multimode fiber converter, ST connector,
-40 to 85°C
ICF-1150-S-SC-T Industrial RS-232/422/485 to single mode fiber converter, SC connector,
-40 to 85°C
ICF-1150-S-ST-T Industrial RS-232/422/485 to single mode fiber converter, ST connector,
-40 to 85°C
ICF-1150I-M-SC-T Industrial RS-232/422/485 to multimode fiber converter, SC connector,
-40 to 85°C, 2 KV isolation
ICF-1150I-M-ST-T Industrial RS-232/422/485 to multimode fiber converter, ST connector,
-40 to 85°C, 2 KV isolation
ICF-1150I-S-SC-T Industrial RS-232/422/485 to single mode fiber converter, SC connector,
-40 to 85°C, 2 KV isolation
ICF-1150I-M-ST Industrial RS-232/422/485 to multimode fiber converter, ST connector,
2 KV isolation
ICF-1150I-S-SC Industrial RS-232/422/485 to single mode fiber converter, SC connector,
2 KV isolation
ICF-1150I-S-ST-T Industrial RS-232/422/485 to single mode fiber converter, ST connector,
-40 to 85°C, 2 KV isolation
ICF-1150-S-SC Industrial RS-232/422/485 to single mode fiber converter, SC connector

Kunder som tittade på denna vara tittade också på
Accept all Reject Configure

This website uses cookies to provide the best possible experience. More information.