DIGI XBee ZB Adapters
ZigBee Adapters for Serial and USB Devices
- Supports the ZigBee PRO feature set
- ZigBee® wireless connectivity for RS232, 485, and USB devices
- Compatible with XBee gateways and modules
- Outdoor RF line-of-sight range up to 1 mile with XBee-PRO®
ZigBee technology enables low-cost, low-power networking of sensors, controllers and other such devices in self-configuring, self-healing wireless mesh networks. Digi´s XBee adapters are used to retrofit existing devices for ZigBee connectivity. Available with multiple interface options, these adapters deliver the benefits of ZigBee mesh networking off-the-shelf, without the development time required when using an embedded solution
XBee-PRO ZB USB adapter, internal wire antenna (International) XA-Z14-CE1P-W
XBee-PRO RS-232 adapter, external RPSMA antenna included (9 - 30V) (International) XA-Z14-CS2PH-W
XBee-PRO RS-485 adapter, external RPSMA antenna included (9 - 30V) (International) XA-Z14-CS3PH-W
XBee-PRO DIO adapter, external RPSMA antenna included (9 - 30V) (International) XA-Z14-CS4PH-W
XBee-PRO AIO adapter, external RPSMA antenna included (9 - 30V) (International) XA-Z14-CS5PH-W
XBee-PRO RS-232 adapter, external RPSMA antenna included (9 - 30V) (International) XA-Z14-CS2PH-W
XBee-PRO RS-485 adapter, external RPSMA antenna included (9 - 30V) (International) XA-Z14-CS3PH-W
XBee-PRO DIO adapter, external RPSMA antenna included (9 - 30V) (International) XA-Z14-CS4PH-W
XBee-PRO AIO adapter, external RPSMA antenna included (9 - 30V) (International) XA-Z14-CS5PH-W
Performance
RF Data Rate
250 kbps
XBee ZB | XBee-PRO ZB | |
Indoor/Urban Range | Up to 133 ft (40 m) | Up to 300 ft (90 m) / 200 ft (60 m) Int’l variant |
Outdoor/RF Line-of-Sight Range | Up to 400 ft (120 m) | Up to 2 miles (3200 m) / 5000 ft (1500 m) Int’l variant |
Transmit Power | 1.25 mW (+1 dBm) / 2 mW (+3 dBm) boost mode | 63 mW (+18 dBm) Int’l version |
Receiver Sensitivity (1% PER) | -96 dBm in boost mode | -102 dBm |
Features
Antenna Type
XBee ZB Adapters: Internal Antenna; XBee-PRO ZB Adapters: External RPSMA Antenna
Frequency Band
2.4 GHz
Serial Data Interface
RS-232 DB9M/DTE or RS-485 (6-position wire terminal block) switch selectable between RS-422 half-duplex, RS-422 full duplex and RS-485
USB Data Interface
USB 2.0 Full Speed (with ESD protection); connects to host via captive 1-meter cable
Analog IO (AIO) & Digital IO (DIO)
6-position wire terminal block; Analog IO: 0 - 10V, 4 - 20 mA, or +/- 2VDC Differential; Digital IO: Digital Input or sinking driver output
Networking & Security
Network Topologies
Point-to-point, Point-to-multipoint, Mesh
XBee ZB | XBee-PRO ZB | |
Number of Channels | 16 | 14 |
Spread Spectrum Type
Direct Sequence Spread Spectrum
Filtration Options
PAN ID, 64-bit MAC, channel
Addressing
65,000 available addresses for each channel
Other
LEDs
Power: Glows green when external power is supplied (not active when battery powered to limit power drain) Associate: Blinks when unit is connected and associated on an RF network
Controls
Device reset (internal push button); Identification (internal push button) – relays ID to gateway
Dimensions (L x W x H) & Weight
RS-232, RS-485, AIO, DIO models: 3.60 in x 1.90 in x 1.20 in (9.14 cm x 4.82 cm x 3.04 cm) 2.29 oz (64.92 g) USB models: 2.87 in x 1.80 in x 0.83 in (7.29 cm x 4.57 cm x 2.10 cm) 1.60 oz (45.36 g)
Operating Temperature
-40° C to +70° C
Power Requirements
Input Voltage
RS-232, RS-485, AIO, DIO models: 3.7-6VDC and 9-30 VDC
USB models:
Bus powered (+5V)
XBee ZB | XBee-PRO ZB | |
Power Consumption | USB: 70 mA (normal operation) / 200 uA (suspend mode) | USB: 70 mA Rx and 250 mA Tx (normal operation) / 200 uA (suspend mode) |
Regulatory Approvals
Emissions
FCC Part 15.247, IC, ETSI/CE, Telec, EN55022 (Class B)
Safety
UL60950, CAN/CSA C22.2 No.60950
RoHS
Yes
Kunder som tittade på denna vara tittade också på